This standard is issued under the fixed designation D ; the number 1 This test method is under the jurisdiction of ASTM Committee D on Soil and Rock. GeoTesting Express is a provider of Soil Testing Services – ASTM D, Standard Test Method for Compressive Strength of Molded Soil-Cement Cylinders. ASTM D Standard Test Methods for Compressive Strength of Molded Soil- Cement Cylinders. MasterLoader Load Frame.

Author: | Faelmaran Goran |

Country: | Tunisia |

Language: | English (Spanish) |

Genre: | Software |

Published (Last): | 2 December 2011 |

Pages: | 167 |

PDF File Size: | 19.39 Mb |

ePub File Size: | 14.35 Mb |

ISBN: | 543-8-60302-282-8 |

Downloads: | 27913 |

Price: | Free* [*Free Regsitration Required] |

Uploader: | Arashisho |

Therefore, the standard unit for mass in this standard is either kilogram kg or gram gor both. It is considered that Method A gives a relative measure of strength rather than a rigorous determination of compressive strength. Add to Alert PDF. In this system, the pound lbf represents a unit of force weightwhile the unit for mass is slugs. As a result, it has been customary to evaluate or specify compressive strength values as determined by Method A.

If the document is revised or amended, you will be notified by email.

### ASTM D – 17 Standard Test Methods for Compressive Strength of Molded Soil-Cement Cylinders

In addition, they are representative of the significant digits that generally should be retained. Sieve sizes are identified by the standard designations in Specification E Height to diameter ratio equals 2. This standard does not purport to address all of the safety concerns, if any, associated with its d16333.

The values given in parentheses are mathematical conversions to SI units, and are provided for information only and are not considered standard. In this system, the pound lbf represents a unit of force weightwhile the unit for mass is slugs.

In addition, they are representative of the significant digits that generally should be retained. It is scientifically undesirable to combine the use of two separate sets of inch-pound units within a single standard. Height to diameter ratio equals 1. In this system, the pound zstm represents a unit of force weightwhile the unit for mass is slugs. Proceed to Checkout Continue Shopping.

The values given in parentheses are mathematical d1633 to SI units, and are provided for information only and are not considered standard. Agencies that meet the criteria of Practice D are generally considered capable of competent and objective testing. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations.

### ASTM D – Standard Test Method for Compressive Strength of Molded Soil-Cement Cylinders

It is scientifically undesirable to combine the use of two separate sets of inch-pound units within a single standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Reliable results depend on many factors; Practice D provides a asm of evaluating some of those factors. Your Alert Profile lists the documents that will be monitored.

It is beyond the scope of these test methods to consider significant digits used in analysis methods for engineering data. It is beyond the scope of these test methods to ast, d significant digits used in astm d methods for engineering data.

Already Subscribed to this document. Also, the equivalent inch-pound unit slug is not given. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

The quality of the result produced by this standard is dependent on the competence of the personnel performing it and the suitability of the equipment and facilities used.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. It is the responsibility astm d the use Therefore, the standard unit for mass in this standard is either kilogram kg or gram gor both. The values given in parentheses are mathematical conversions to SI units, and are provided for information only and are not considered standard.

Height to diameter ratio equals ast.

## Active Risk Management

The values given in parentheses are mathematical conversions to SI units, and are provided for information only and are not considered standard. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Note 1-The agency performing this test method can be astm d in accordance with Astm d D Therefore, the standard unit for mass in this standard is either kilogram kg or gram gor both. Link to Active This link will always route to the current Active version of the standard. Historical Version s — view astm d versions of standard.

It is considered that Method A gives a relative measure of strength rather than a rigorous determination of compressive strength. It is considered that Method A gives a relative measure of strength rather than a rigorous determination astm d compressive strength. Link to Active This link will always route to the current Active version of the standard. This use combines two separate system of units, the absolute system and the gravitational system.

Not withstanding statements on precision and bias contained in this test method: Historical Version s – view previous versions of standard. Therefore, the standard unit for mass in this standard is either kilogram kg or gram gor both.

You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server. This implicitly combines two separate systems of units; that is, the absolute system and the gravitational system. As stated in 1. This implicitly combines two separate systems of units; that is, the absolute system and the gravitational system. This standard is not included in any packages. Users of this standard are cautioned that compliance with Practice D does not in itself ensure reliable results.