GY520 MANUAL PDF

Futaba GY Pdf User Manuals. View online or download Futaba GY Instruction Manual. Nstruction, Anual • Read online or download PDF • Futaba GY User Manual. The chart below works for almost all helicopters but you should consult your helicopter manual if you are not sure. Note that I have seen.

Author: Grok Faekree
Country: Mauritius
Language: English (Spanish)
Genre: Automotive
Published (Last): 28 April 2009
Pages: 146
PDF File Size: 9.58 Mb
ePub File Size: 19.94 Mb
ISBN: 513-2-88313-578-2
Downloads: 7366
Price: Free* [*Free Regsitration Required]
Uploader: Shakakazahn

Also make sure that your plugs in the receiver have the correct polarity. The first thing to do is make the link slides as free as possible. Make sure you can get to the button on the gyro. When you mount the gyro, use the supplied foam tape.

FUTABA GY520 Manuals

The blue label on the gyro needs to be either up or down. That is the servo limit setting mode.

Remove Advertisements Sponsored Links. Just hold it on top of the ball. The black wires of every plug all should be on the same side of the receiver. The black wires will be away from the labels. To get the tail to move faster or slower, adjust the rudder channel travel. You will see the servo move to one side. There are three things that need to be connected. Power up the radio and the receiver. Then the light will stay on solid.

It puts the gyro in a standard rate mode so the servo will center when the rudder stick is centered. The color of this 4-Blink indicates the mode it is in.

  KONGRESNI TURIZAM PDF

GY Setup – HeliFreak

With it in this position the gyro will be in heading hold with the gear switch up position 0. This would be very simple for Futaba to have done and would save some confusion.

My setup on the miniTitan is Register Now In order to be able to post messages on the HeliFreak forums, you must first register. From the servo limit function, hold the gyro button down for 2 seconds to get to the Flight Mode selection. On my miniTitan you can see in the right gy20 that the tail servo is mounted to the tail boom. Do not tie the soft rubber line down to the helicopter, close to the gyro. Note that I have seen common problems with the tail blades grips mnaual the wrong direction and the tail belt twisted the wrong direction.

Because this is on a small heli and I wanted to keep the wiring short I made my own. Most other receivers have it labeled channel 5. Note that passwords are case-sensitive. Move the nose of the helicopter left and verify the trailing edge manuaal the tail blades move to the right. When the stick is centered it needs to be a solid color red HH, blue non-HH.

That is the difference between one value having a positive value and the other a maanual value. In the picture on the left you see I am not using them.

For the first second the light will blink slow. The light will change to a violet color. This will tell you the current mode the gyro is in.

  BABE IN BOYLAND PDF

So it is important to make the checks on the bench so you do not risk damaging the helicopter. Do not stick the gyro to the side of the frameset. If you need to readjust then quickly press and release the gyro button.

Futaba GY User Manual | 32 pages

Thank you so much! At the left, look at the top picture. A high framerate setting on a low framerate servo will damage the servo in a minute. Do the same for ‘GEAR’. On majual Trex not Pro some people turn the block upside down that the tail boom goes in then mount the gyro under the rear of the kanual. You should make the decision based on what your flying style is.

The next second it will blink fast. Move the rudder stick right and verify the trailing edge of the tail blades move to the right. Please click one of the Quick Reply icons in the posts above to activate Quick Reply. Quote message in manul In order to be able to post messages on the HeliFreak forums, you must first register.

If all of this checks good then continue to step